Waste Ink Pads

□ Part/Unit that should be removed before removing Waste Ink Pads

Document Cover / ASF Cover / Support Arm / Scanner Unit / Middle Case / Panel Unit / Printer Mechanism / Hopper / Main Board / Main Frame / EJ Frame Assy. / Print Head / CR Scale / CR Motor / CR Unit / Timing Belt / Ink System / EJ Frame Assy. / EJ Roller / LD Roller / ASF Unit

□ Removal procedure

1. Remove the Waste Ink Pads (x8) from the sections indicated with ® to © of the Frame Base.

Cx5500 Waste Ink Pad
Figure 4-84. Removing Waste Ink Pads

CAUTION

When removing the Waste Ink Pads, be careful not to tear the tip of the induction paper. If it is torn, replace the induction paper.

When installing the Waste Ink Pads, be sure to insert ribs and tabs of the Frame Base into the slots and notches of the pads. When installing (2) in the section (§) (refer to Figure 4-84), be sure to match the positioning tabs and press (2) until it clicks to secure it in the right position.

When installing the Waste Ink Pads on the section , be sure to lay the six parts one on top of another in the order shown in the figure.

Figure 4-85. Installing Waste Ink Pads (1) When installing the Waste Ink Pads on the section (B), make sure to insert the tips of induction paper between the © and © pads.
Epson Artisan Ink Pad
Figure 4-86. Installing Waste Ink Pads (2)

After replacing the Waste Ink Pads, perform the following adjustment (TBD). (Refer to Chapter 5 " ADJUSTMENT (p100)")

"Waste Ink Pad Counter" (only after replacement)

"Ink Charge"

"TOP Margin Adjustment"

"Head Angular Adjustment"

"Bi-D Adjustment"

4.6.12 PF Roller

CAUTION

Do not touch or damage the coated area of the PF Roller Assy., when performing the following work. When installing the Spur Gear, 13.5, be sure to install a new one. The Spur Gear 13.5 cannot be reused.

□ Part/Unit that should be removed before removing PF Roller

Document Cover / ASF Cover / Support Arm / Scanner Unit / Middle Case / Panel Unit / Printer Mechanism / Hopper / Main Board / Main Frame / EJ Frame Assy. / Print Head / CR Scale / CR Motor / CR Unit / Timing Belt / Ink System

□ Removal procedure

1. Remove the FB Cover.

Epson Stylus Photorx560 Waste Ink Pad
Figure 4-87. Removing PF Roller (1)

CAUTION

When removing (prying) the Spur Gear, 13.5 with a flathead screw driver or the like, do not use the fragile upper half of the bearing as a pivot point, but use the firmer lower half instead.

Lower half of the Bearing

Driver Epson Stylus 4400 Wxp

half of the Bearing

Spur Gear, l5T|

Figure 4-88. Removing Spur Gear, 13.5

half of the Bearing

Spur Gear, l5T|

Lower half of the Bearing

Figure 4-88. Removing Spur Gear, 13.5

2. Remove the Spur Gear, 13.5 from the PF Roller with a flathead screw driver or the like.

Epson Printer Stylus 4450
Figure 4-89. Removing PF Roller (2)

3. .Pull open the bearing slightly (Arrow (!)), and remove the PF Roller Assy (Arrow (2)).

Epson Stylus Photorx560 Waste Ink Pad
Figure 4-90. Removing PF Roller (3)

When the PF Roller is reassembled, perform the required lubrication. (Refer to Chapter 6 " MAINTENANCE (p108)")

4.6.13 PF Motor

□ Part/Unit that should be removed before removing PF Motor

Document Cover / ASF Cover / Support Arm / Scanner Unit / Middle Case / Panel Unit / Printer Mechanism / Hopper / Main Board / Main Frame / EJ Frame Assy. / Print Head / CR Scale / CR Motor / CR Unit / Timing Belt / Ink System / PF Roller

□ Removal procedure i. Detach the ferrite core from the Frame Base.

Figure 4-91. Removing PF Motor (1)

2. Remove the screws (x3), and remove the PF Motor.

Epson Printer Stylus 4450
Figure 4-92. Removing PF Motor (2)

When installing the PF Motor, arrange the cable into the slit and the hook, then place the ferrite core into the positioning hole.

Epson Stylus Cx5500 Scanner
Figure 4-93. Installing the PF Motor

Was this article helpful?

0 0

Responses

  • Costantino Arcuri
    How to change waste ink pad epson dx4450?
    8 years ago
  • Lena
    What happened to epson if waste pad is full?
    8 years ago
  • brogan
    How to change ink pad epson dx4400?
    8 years ago
  • TIM
    How to set waste ink counter on DX4450?
    8 years ago
  • luam
    HOW TO REPALACE WASTE INK EPSON CX4300?
    7 years ago
  • Beverly
    How to replace an ink pad epson dx4450?
    6 years ago

Post a comment