Maintenance ASSY Removal

When you replace the Maintenance ASSY, ink can spill from the ink tube connected to the pump assembly. Disconnect the ink tubes carefully so that ink will not spill. 1. Remove the R Side Cover. (p.160) 2. Remove the Access Cover. (See Removing the Access Cover on page 167) 3. Disconnect the connector (CN17) of the Pump Motor ASSY. 4. At the rear of the printer body, remove the four screws securing the Maintenance ASSY, and remove the Maintenance ASSY from the printer body. (See Figure 4-72)...

Cleaning Mechanism

The cleaning mechanism in this printer is compatible with the cleaning mechanism in the Stylus Pro 5000 9000. The cleaning mechanism is located on the right side of the printer. The waste ink from the cleaning mechanism is channeled to the waste ink pad (Maintenance Tank) in the lower right side through the tube. The cleaning mechanism components are installed above the sub-frame and some are fixed on the main frame as shown below. Pump assembly (head cleaner) When the head is in the capped...

Epson 9600 Ink Cartridge Sensor Connectors

Epson Stylus Pro 7600

You must execute ink discharge Ink Blowing in 5.2.3.20 Clean Head on page 256 before removal of the I H ASSY and ink charging Initial charge in 5.2.4 Cleaning on page 259 after reinstallation. If no ink tube is to be removed, there is no need of executing ink discharge. When removing and installing the front cover switch holder, the following adjustment should be made. Refer to 5.1.4.9 Cover Sensor ASSY Adjustment p.216 1. Remove the R Side Cover. p.160 2. Remove the L Side Cover. p.163 3....

PF Encoder Sensor Installation Position Adjustment

Sensor Epson

This adjustment is performed to set the distance between the PF roller shaft grid roller and PF encoder sensor in the proper position. Through this adjustment, the position of the PF encoder sensor's emitter and receptor are set properly with respect to the slits in the loop scale for the PF motor. Adjusting tools PF ENC Installation Position Adjustment Tool F798 1. Loosen the one screw securing the PF Encoder Sensor, then put the round hole of the PF Encoder mounting jig on the PF Roller Shaft...

CR Board ASSY

Remove the R Side Cover. p.160 Remove the L Side Cover. p.163 Remove the I H Cover. p.164 Remove the H Top Cover. p.165 Remove one screw CPP M3x6 , two screws CP W M3x6 and one screw M3x16 securing the CR Board Guide, and also the ground line and the toothed washer M3 , and remove the CR Board Guide. See Figure 4-30 Disconnect the following eight connectors with lock connected to the CR Board. 7. Remove the two screws CPP M3 x 8 securing the CR Board ASSY and remove the CR Board ASSY. See...

Flushing Box ASSY

Remove the Paper Guide L2. p.168 3. From the printer body, pull off carefully the waste ink tube thick which connects the Flushing Box ASSY to the Maintenance Tank. 4. Remove the one CUPS M3x6 screw securing the Flushing Box ASSY. 5. Take out the Flushing Box, while pulling off carefully the waste ink tube thin coming from the Pump ASSY. 6. Remove the Flushing Box ASSY. After installing the Flushing Box ASSY, make certain by removing the Paper Guide L2 that...

PF Encoder Sensor ASSY

Encoder Epson

Disconnect the PF Encoder Sensor connector. 3. Remove the one screw securing the PF Encoder Sensor and remove the PF Encoder Sensor ASSY. After installing the PF Encoder Sensor ASSY, make the following adjustment. 5.1.4.10 PF Encoder Sensor ASSY Adjustment p.216 Figure 4-52. Removing the PF Encoder Sensor. Figure 4-52. Removing the PF Encoder Sensor.

Epson Stylus Pro 7600 Command Error

Note The status can't be replied during service call. Warning warns the user of the occurrence of a corresponding event by replacing the READY or PRINTING message on the LCD with the warning message. But it has no effect on any other operations of the printer. The warning message will not be cleared until the cause is resolved. Table 3-2. Warning Indications on LCD Table 3-2. Warning Indications on LCD

Platen Gap Adjustment Unit

Head Epson 2180

In order to maintain the print precision, it is necessary to maintain the carriage head mounting position so that it is always a constant distance from the surface of the paper. In this printer, the print head nozzle surfaces and platen surface are variable mechanisms so that the gap between the paper printing surface and the head nozzle surface can be kept constant. The carriage has a 2-body construction with a sub-carriage on which the print heads are mounted attached to the carriage which...

What Is An Epson Pf Motor

Epson Motor

Disconnect the one connector cable of the PF Motor ASSY and take it out through the hole in the L Side Frame. 3. Remove the four screws securing the PF Motor Mounting Plate. See Figure 4-51 4. Move the PF Motor toward the printer body and remove the PF Motor by lifting the gear side. After replacing the P_EDGE Sensor, the following adjustment operation should be performed. Figure 4-50. Removing the PF Motor ASSY Harness Connector. Figure 4-50. Removing the...

Troubleshooting for Service Call Errors

If any service call error has occurred, Stylus Pro 7600 9600 inhibits interruption, restores the actuators to their respective initial positions, writes the NVRAM values as a rule, and makes all the LEDs on the panel flash. Occurrence of any error from which the user can not recover the printer. Life expiration of a long-life part which can cause secondary problems if the part is further used. The printer has been brought into malfunction by unexpected operation or by receiving an unexpected...